Denso Liquid Coatings
For Technical Data Sheets, please click for our Catalog.
Protal is Denso’s line of protective pipeline coatings that can be applied by hand
or spray method. We offer a full range of fast cure, high build epoxies for a variety
of above and below ground corrosion protection. Our Protal Liquid coatings can easily
be applied in high and low temperature environments. Our anti corrosion coatings
are also great for protecting girth welds, tie-ins, cadwells, fittings, fabrications,
repairs to FBE and rehabilitation to existing pipelines. Our pipeline coatings are
high build, up to 50 mils in one coat.
Liquid Coatings Brochure
Protal 7200 - High build, fast cure pipeline coating
A fast cure, one coat epoxy coating that can be hand or spray applied to girth welds,
tie-ins, fittings and rehabilitation of existing pipelines. Exhibits excellent cathodic
disbondment properties at 175°F (80°C) with 7 mm disbondment.
Protal 7200 Repair Cartridge - Fast Cure Epoxy Repair Coating
Repair coating for damaged FBE and other liquid coated pipelines. Also used as coating
of cadweld areas.
Protal Air Cartridge Gun (1000 ml) - For Spraying Cartridges of Protal Liquid
Can be used in a wide variety of spray applications using Protal Liquid Coatings.
It is designed for use where fast and easy setup, no clean up, minimal material
waste and minimal equipment maintenance is needed.
Protal 7200 Cartridge (1000 ml) - Fast Cure, High Build Spray Applied Pipeline
Protal 7200 Cartridge (1000 ml) is a VOC free, 100% solids, 2 part epoxy coating
specially formulated to compliment FBE coated pipe.
Protal 7250 - High build, fast cure pipeline coating
A fast cure, one coat epoxy coating that can be spray applied to girth welds, tie-ins,
fittings and rehabilitation of existing pipelines. Exhibits excellent cathodic disbondment
properties at 175°F (80°C) with 7 mm disbondment. Protal 7250 is used in Canada
only and is the spray grade version of Protal 7200.
Protal 7000 - High build pipeline coating - brush grade
A fast cure, one coat epoxy coating that can be hand applied to girth welds, tie-ins,
fittings and rehabilitation of existing pipelines.
Protal 7000 Airless Spray - High Performance Epoxy Coating
Solvent free two-pack high build high performance epoxy coating which is applied
with conventional airless spray equipment.
Protal 7125 - Fast cure, low temperature pipeline coating - winter grade
A low temperature coating that can cure at -4°F (-20°C). The coating can be backfilled
in 30 minutes at 50°F (10°C). Used for girth welds, tie-ins, rehabilitation, repairs
to FBE and sacrificial coating to FBE.
Protal 7125 Repair Cartridge - Fast cure high build pipeline repair coating
A fast cure pipeline coating that is packaged in cartridge tubes and applied with
a dispensing gun. The coating can be backfilled in 30 minutes at 50°F (10°C). Used
for girth welds, tie-ins, repairs to FBE, rehabilitation, sacrificial coating to
FBE and caldwelds.
Protal 7900HT - High temperature pipeline coating
A high build epoxy coating that can be hand applied to girth welds, tie-ins, fittings
and rehabilitation of existing pipelines. Maximum operating temperature up to 302°F
Protal 7300 - Moisture Tolerant Pipeline Liquid Coating
Protal 7300 is a VOC free, 100% solids epoxy coating specially formulated to coat
dry, damp or wet surfaces. It is a high build liquid coating that is Denso Protal
Applicator Pad, Denso Protal 9" Roller, or brush applied in one coat in the field
Protal ARO - Abrasion Resistant Pipeline Coating
Protal ARO is a VOC free, 100% solids liquid epoxy coating formulated to be applied
over FBE as an ARO coating (abrasion resistant overlay). It is a 3:1 ratio compatible
for most plural component spray units coating that can be spray or hand applied
in the field or shop.
Protal ST Epoxy Mastic - Surface tolerant liquid epoxy
A fast drying surface tolerant epoxy coating that can be hand or spray applied to
wire brushed rusty steel surfaces. Used for above and below ground pipelines, structural
steel, bridges, tanks, and other steel surfaces.
Denso Bitumen Mastic - Single component bitumen mastic coating
A high build single component cold applied liquid bituminous coating. Used for corrosion
protection of buried pipe, flanges, valves and fittings.
Denso Weathershield 65 - High Solids Aliphatic Polyurethane
Used as a topcoat over Protal Liquid Coatings to provide color coding, abrasion
resistance, chemical resistance and UV stability. Will cure at temperatures as low
as 40°F (4°C).
Denso OuterArmour - Liquid Epoxy Topcoat for Denso FB 30 Tape and Denso Glass Outerwrap
Denso OuterArmour is a two-component 100% solids liquid epoxy coating. It is a tough/durable topcoat that provides excellent
abrasion resistance for Denso FB 30 Tape and Denso Glass Outerwrap.